Search results

  1. Gravy

    Fuel Cell Foam - School me!!!!

    Step 1 throw away the foam. Step 2 gas safe wiffle balls or PVC pipe cuts
  2. Gravy

    General Tech What did you work on Today?

    A little upholstery job tonight
  3. Gravy

    My new ride

    I love the 5.9 Durangos. My dad got a ticket pulling our boat over Vail pass at 90 plus miles per hour. He framed it.
  4. Gravy

    What do I get for the next bike?

    When you put the whole bike together and then find a leak and have to take it apart and then put it back together again....
  5. Gravy

    What do I get for the next bike?

    I ran it. It worked amazing and the bike has better power than ever. It's super snappy and feels great with the jetting change. I'd still like to experiment with a better shaped head for improved gas mileage and hopefully some power- then I could gear up and have some longer gear ratios and...
  6. Gravy

    Weld table idea

    I've got an old butcher counter with a fat piece of plate steel on top. The drawers are super sturdy. It's quite deep and great for working on multiple projects at once and I don't have any qualms about tossing a tcase or motorcycle motor up on it, then wiping it down and tig welding too.
  7. Gravy

    Favorite camp chairs

    I prefer to sit on the wet ground, balance on a rock or odd shaped uncomfortable log. I'll have to try these chair things out.
  8. Gravy

    #yamaproblems : a rebuild thread

    Polisport plastics just featured my build. Feels nice to do a thing. :cool:
  9. Gravy

    Free IFS toy steering box: FREE

    still have this
  10. Gravy

    What do I get for the next bike?

    2.1-2.14 mm squish. Lots. I'm told I can go down to 1.3 mm safely on pump gas. That's with a 0.5 mm base gasket I'm basically flush with the exhaust and transfer ports at BDC. Do I swap to a 0.2 mm base gasket (which only nets me 1.8mm squish),(0.3mm gain) or get an Aftermarket / milled head?
  11. Gravy

    What do I get for the next bike?

    Pretty
  12. Gravy

    What do I get for the next bike?

    Notes for me: Pete says 200cc in both forks.
  13. Gravy

    Wanted Training Wheels for a little motorcycle

    Russ when both tires leave the ground you're supposed to land back on those two tires not on your handlebar and the side of your body on a rock....
  14. Gravy

    Micropolishing

    I like that the exhaust flange uses an o-ring. I put off rebuilding power valves because I have to scrape high temp silicone on my other bikes every time...
  15. Gravy

    Van conversation

    I'd say! That's enough power for a back to the future Deloreon!
  16. Gravy

    Van conversation

    Ha. I drove a 1998 Dodge B2500 for work for years. 381,000 miles when sold, and the 360 would still melt the tires. 4.10's I literally only had to do ball joints twice. plugs and wires and rotor cap once or twice and brakes 2 times. We had the trans rebuilt at 180k and it was solid as a rock...
  17. Gravy

    Wanted Training Wheels for a little motorcycle

    make one a set. I did with some harbor freight dolly wheels and 2 small ubolts and a piece of allthread with washers and nuts
  18. Gravy

    What do I get for the next bike?

    Thanks for the heads up. Should be OK. Andrew Cooksey is measureing 72.7mm on the OEM skirt. Edit: I measured my stock piston at 72.7mm also.
  19. Gravy

    What do I get for the next bike?

    Ring gap: .012-.014 Base gasket: .48-.5 mm (same gasket as pre 2017 motors oddly enough). Power valve z measurement: stock Power valve actuator is a little different than the 2011-2016
  20. Gravy

    Free IFS toy steering box: FREE

    yup its free! come get it, if you bring me a Dr. Pepper I'll be your friend.
Top