Search results

My 06 Dodge with a hemi is getting pretty bad mileage right now. 8.3mpg on this last tank, 230 miles driven and it took 27.55 gallons. That matches up with my overhead console too. It's been like this for months now. I've had the truck a year, and I've only seen double digits in rare occasions...

I've had this trailer for a few years, and it's been a good little trailer. It's made by Snowbear and appears to have a manufacturer date of 02/07/2002, and a GVWR of 2090lbs. 4ft 8in-ish wide by 8ft-ish long. The trailer has a pivot deck, and all side panels are removable. I put new lights and...

I bought these in early 2022 from another member on here. I was going to use them in my Cherokee, but I'm selling it this week. I haven't opened the covers yet, but I was told they have 4.10 gears, a front Spartan helical lsd, and the rear has zj disc brakes. Let me know if you're interested...

I was going to change my ball joints this weekend, but my hubs are seized into the knuckle. I've tried all of the tricks and brute force I have. Do any of you guys own this tool: https://www.napaonline.com/en/p/OTC6290A?impressionRank=1 I'd like to rent it from you. I think it's my last hope.

Is there an acceptable amount of vertical ball joint movement? I feel like there shouldn't be any movement vertically. I was putting new brakes on my Dodge and noticed there is about a 1/4" of vertical movement on the knuckle.

I'm looking for a shell for my 06 mega cab with a 6ft 4in bed. Preferably silver, white or black, but I'll look at others too. Thanks.

My brother's transmission on his 99 power stroke is toast, so he's looking to get it rebuilt. He talked to this guy off of ksl, and he seems pretty knowledgeable. Do any of you know this guy, or heard of him? Rebuilt 4R100 and Ford Transmission https://classifieds.ksl.com/listing/66533648

My trailer has a large amount of play in the coupler, and I'm wondering if it can be rebuilt. This is the style of coupler.

Where do you all get braided oil/fuel lines made? My coworker wants to have some made for his first gen Cummins. Specifically the oil feed to his turbo. He said the ERIKS here in Ogden said they don't make them, which I thought was weird.

I believe that the voltage regulator in the PCM has failed on my Cherokee. I have read that I can wire in an external regulator to get my alternator charging again, but I'll still have a dead voltmeter gauge and a MIL. If you have done this swap before, how did you fix these issues? Electrical...

My coworker is looking for two tires in this size for his ratrod. Anything close to the bogger style. Let me know if you have anything. Thanks.

Does anyone in the Davis /weber county area have the front hub seal driver tool for the super duty axles? I would like to borrow it if you are willing.

I'm replacing the clutch on my dad's liberty, and I'd like to have a more secure way to support the transmission. What have you guys cobbled up to attach to your floor jack? I'd rather not spend the money on a dedicated transmission jack.

Do you guys run a traction bar on your tow rigs? My brother put a 2in lift block on his truck and now it has pretty decent spring wrap even just switching from R-D. I can only think that it is worse when pulling a trailer, which this truck will do 75% of the time. If you run one, what...

My brother put a Carli Suspension Torsion style sway bar on his 3500 Dodge. It had no key/alignment marks to get the arm pieces on the torsion bar in the exact same spline as the other side. In my mind, ideally you would want the bar in a neutral state(arms on exactly the same spline) at ride...

Anyone know where I could rent a torque wrench that goes above 280ft lbs?

After hearing about @SoopaHick's woes, I decided to check out my rear drive shaft's condition. I couldn't get the slip joint to move by hand, but I could pump a bunch of grease into it and it would move slightly. As well as pushed some brown rusty grease mixture out of the splines. What are my...

I'm looking to buy some tube inserts like these: https://www.ruffstuffspecialties.com/catalog/125-HEX.html Where is your favorite source, local or online?

Do any of you do asbestos testing/removal? I have some ceiling tile and old floor tile I'd like to get tested before I go ripping it out.

Is there anybody local that sells exhaust flanges for a decent price? I'm just looking for a simple 2 bolt 2.25" weld on flange. I'd probably need 6 of them.