Search results

Hey guys, I'm looking for a 4.10 gear set to run larger tires. The aftermarket is obsolete on this diff, only 4.56 is offered by Yukon. This is the Dana 35 ttb reverse cut commonly found in '91-'94 Explorers and '90-'97 Rangers. Let me know if you have a parts rig laying in the backyard, or know...

Hey guys, I tried doing a night run up Old Ward trail in Bountiful last night to test my new lights out. Looks like it will be closed to anything wider than an ATV for quite some time. This landslide happened roughly 1/3 of the way up and it looked like a 10’ drop to the steep hillside below.

I’m taking my family up forest lake trail tomorrow morning. I have three kids so it’ll be a bit to get going in the morning, but I hope to be to Ridleys by 9:30 or 10. Sorry for the odd day, it my only day off.

I'm planning to take my wife and kids up Old ward canyon Saturday afternoon around 1:30 or 2 to test the 33's I put on. Anybody is welcome to tag along!

Lightly smoked stock 1st gen Explorer tail lights. The red led is Phillips and did not require a new flasher to work properly. The reverse lights are jdm astar and are extremely bright! Price firm.

This axle was built to handle 40's. I did all the work myself and have receipts for all parts. The axle is bare other than stock spring mounts, and primered. Here's the goods: ARB air locker Yukon 5.38 gears Crush sleeve eliminator Spicer 1410 Yoke New Timkin bearings and races in the hubs, and...

Roadmaster's hidden tow bar mount for 1st gen explorers. Could also fit rangers or b2's of same era. Frame mounts use three bolts in existing holes, then using hitch pins, the tow bar mounts are removable for a clean installation. Standard tow bars mount no problem, and it tows like a dream. $200

Ground clean, then clearcoated. Fits 2" receivers. $10

Here is a built Sterling 10.25 axle. I have done all the work, and have all receipts. The list of parts is as follows: New timkin bearings and races new hub seals Yukon 5.38 gears crush sleeve eliminator ARB air locker 1410 yoke ruffstuff disk brake brackets e-350 brake rotors painted to...

I have just the block, I tossed all the internals as I was going to stroke it. I pulled it from a '96 F-150, so it's roller ready. I do still have all the front accessories, brackets, and ps pump, along with the upper and lower intake manifolds. $200

I am planning a run out there this weekend. I have a fullsize Ford I'll take, and there are 2 to 3 Jeeps that should be coming so far. I'm not sure where to meet, but it will be in Vernal somewhere. I haven't run the trail before, so any seasoned wheelers of this trail are more than welcome to...

If anybody is interested in a well built metal Jerry Can, I saw some 5 gallon red cans for sale at State Trailer Supply on Washington and 31st in Ogden the other day. Prices were not listed however, but they had plenty on the shelf.

This will be my first time up there this season. So far its me in my F-150, my buddy in his leveled stock '06 F-150, and possibly a couple JK's. I don't know how far up mineral basin we can get after (we had to turn back at the first big rock because of the newer F-150) but we may try that after...

Tried doing a trail run up old ward last night to have a fire with friends and didn't get very far before we ran into this. Anybody have any information on it? The jeep was cold, so it had been there a while. Just looked like they rode too high on the trail and rolled it. There were no...

Here are some pics of my rig from the past couple years.

Hey guys! New to this forum but not to wheeling. I've got a 1991 F-150 with the 302 in it. I've done extensive mods to it, too many to list but here are a few noteworthy ones: lockright locker in rear axle, sliders, custom gas tank and transfer case skids, clocked transfercase for clearance...