Search results

Let me start with saying this is a problem with my brothers 1998 Cherokee. I will give as much information as I have and try and relay all pertinent information as I get it. My brother purchased a 1998 Cherokee some time ago and has run fine. While driving to work at HAFB the jeep started...

I recently put a rear scout dana 44 in my jeep scrambler. Today while driving I could hear a clanking sound. I found my drivers side rear axle shaft had started to pull out of the housing. I found some retention plates that say they "eliminate pull through". Is this what it is called? also...

I have a dana 44 that is full width. The previous owner said it was from a dodge. It has chevy flat top knuckles on it, one side is drilled the other is not. I am not using it and I need it out of the garage... located in clearfield come get it. I work graves so no early morning calls...

I have upgraded my axles to dana 44's and have these spare shafts laying around. One set is Warn HD shafts that are 44 shafts that have been necked down to fit a dana 30. The other pair are stock shafts. asking $50 for everything. Scott-801-809-7746

I bought this axle for the gears and locker. I have everthing minus the cover and gears and locker. Brakes and warn hubs are brand new. Scott 801-809-7746 This will be scrap in a week or so...

like the title says I need chevy dana 44 small bearing spindles. Let me know what you have. I beleive they were found in chevy axles in the early 70's thanks in advance Scott

I am converting a chevy housing to 5x5.5 so all I need is the knuckles out. Let me know whats out there. Scott 801-809-7746

I purchased this with the intent of swapping it into my jeep. I then purchased a set of axles that fits my needs better. This axle is 62" wms to wms 33 spline shafts with 4.90 gears and an ARB locker. The lug pattern is the chevy, nissan, toyota pattern. This is a stout rear axle, I dont...

I purchased an axle that has a set of 5.38 gears in it. I am runnings 4.88's so I have no need for this set. $50 great condition no signs of wear. Came from a chevy dana 44 scott 801-809-7746

I am looking for a good 4.88 Ring/Pinion for a dana 44. Let me know what is out there. Also a ARB for same dana 44. scott 801-809-7746

I am interested in a wagoneer model 20 the cheaper the better...I would like a complete axle. 801-809-7746

I am replacing the seals on my dana 300 and I cant figure out how to remove the shift rails.

Am I better off using paper gaskets??? on the transfer case or is it better to use RTV??? Opinions and expieriences are welcome. I am getting ready to put the dana 300 back in my scrambler and I want to make sure it is not leaking I bought all the seals from NAPA so now I need to know if it is...

I have a junkyard TBI on the AMC 360 thats in my scrambler. It is up and running but seems to be a little rich. The chip is one that was modified for the engine but I believe it could be dialed in a little more. Is there any shop that I can trust to do this or should I buy the cables and...

How well will a dana 30 with 4:10's and ARB hold up with 35"s??? The jeep is used on and off road and the wheeling is moderate If I try and dont suceed, I dont keep trying till I break something. I am also running a amc 360 and a auto trans if that matters....

I have a 1983 scrambler. It is sprung over with 35's I am looking to buy a small tent trailer and have heard it is not wise to tow with a spring over. I have looked at other trucks and alot of them came from the factory this way. Just looking for a little more information. Thanks in advance.

I put a chevy TBI on my amc 360 jeep starts then and will run...kind of. The engine is is dumping black smoke and is lumping???? Does any one know if the TBI have a stock regulator or if I need to get a inline? It seems as if the injection is flooding the engine out. Thanks for any help of...

Are the valley pan gaskets used under intake manifolds on jeep 360's reusable?

Has anyone done this swap? I picked up the harness, throttle body, and sensors today and wondered if theres anyone who has done this and might have some advice. Thanks

Does anyone know a shop that I could get a piece of aluminum for a cj dash? I would aslo be interested if the could cut some of the holes for me. thanks