Ford Brian's bronco 2 gets wontons and dddd

YROC FAB.

BUGGY TIME
Vendor
Location
Richfield, UT.
Bumpity. Typical last minute pimp out of the bronco. He wheeled the shit out of it all spring and summer. Some time in the spring he broke his tranny mount and we repaired it and made a little skid plate. Then in the summer we was crawling it hard and then hauling ass on a dirt road right after to get to another trail and the flex plate broke. It has been parked since. Well with koh coming up and brian wanting it to work he started looking for anther tranny to put in it since the old one was also shot on top of the broken flex plate. Since its a crappy tranny that means no one had one and any one that had one wanted an arm and a leg for one. I told him to just buy another bronco so he searched ksl for another bronco and all he found was ones 5-6 hrs away for a grand or more. He then got on FB and did ISO bronco 2s and with in an hour he had a dozen offers. One guy in laverkin gave him two broncos for free and he found another one in price for 200$ and one close to home for 250$. So for 450$ and gas money he had 4 broncos in a few days lol. All the broncos he found where in good shape and could be daily driven with minimal work. The one close to home just had a new clutch installed and they just never finished putting the drivelines and slave cylinder in, another one had the tank removed because it was dirty and never got a new one installed. 3/4 are suppose to have good engines. They are all manuels so he is going to convert the crawler bronco to a manual and we are going to dual up his bw1350's. We tease him now about how he has a herd of wild broncos in his yard lol.

49114011_1210542539102403_789773094788005888_n.jpg
He yanked the good tranny today. He said he is going to tip the crawler over too to take out the auto lol. 49784368_2445832822097514_8474377337259950080_n.jpg
 

YROC FAB.

BUGGY TIME
Vendor
Location
Richfield, UT.
Just read this entire thread. I think you could cut some more bronco's into plate:rofl:. Awesome build.

The ones welded to his front of his doors was suppose to be the sides for the spare fuel jug but they were the wrong size so i welded them on against his better judgment lol. I may cut out some My little ponys for it also against his better judgment.
 
Last edited:

YROC FAB.

BUGGY TIME
Vendor
Location
Richfield, UT.
We got it into brians Hobo garage and nailed up a tarp to keep some heat in and he got after it. He got the old tranny out and is working on installing the manual. i have a couple cases at my house waiting for me to dual up.


49705067_1139176172926203_9072117797089181696_n.jpg49209711_1644330612533231_6850910812115042304_n.jpg49263623_2159485757702243_9027195067693006848_n.jpg49348592_590480334737189_3445106457689718784_n (1).jpg49545901_300804770569113_7424759507042959360_n.jpg49899024_138959866990005_5905997253713068032_n.jpg
 

YROC FAB.

BUGGY TIME
Vendor
Location
Richfield, UT.
Dual Borg Warner 1350. That sucked big time. Should work good. Stock 1350 cases are 2.48. He has 6.15:1 with both in low now. That gutless 2.9 should be able to crawl finally. Hes got the manual trans in and is going to stab the cases tomorrow and this weekend we will get it mounted and cut/lengthen the d lines just in time for koh.

I ended up installed the rear case shift tab and shifting it into low and then welding it right to the adapter plate so it will just stay in low all the time now. The sad little motor is useless in high anyway even with 5.38 axle gears, its just too much weight for the motor, and brian will never drive faster than 50mph which it may be capable of doing in low. Also we know brian all too well and he would eventually forget and would shift the front case in low and leave the rear case in high and that would explode the welded shaft.
 

YROC FAB.

BUGGY TIME
Vendor
Location
Richfield, UT.
We got it in the shop. We reused the x member, but just moved it back about 6" and redrilled the frame and then we made a new tranny mount. Still need to put a mount on the t cases. Brian installed carpet and new seats out of one of his other broncos. We ended up tipping another bronco over at 4am to rob a oring off the clutch master cylinder hose where it goes it to the slave cylinder, It was ridiculous.
Zero paragraphs used because dont care. Swapping the column brace over to a clutch pedal one was also a giant pain. i got the d lines lengthened, shortened and installed. we got the all the fluids topped off, and the clutch bled. it still needs needs a column mount, rewired the fan and front led lights as they use to go through the fire wall hole for the clutch master cylinder.

50570678_310047302982516_2610959723599495168_n.jpg50980872_2069672446415991_152442124640452608_n.jpg51068873_340096423383759_8600261394186633216_n.jpg50608256_2322444344466958_609599826606161920_n.jpg51300786_972727213115733_7132289358219968512_n.jpg
 

YROC FAB.

BUGGY TIME
Vendor
Location
Richfield, UT.
Kaboom! It wheels damn good now. He crawled all the F'ed buggy lines at koh that me and austin was taking. We did some wheeling since we have been home and the other day while he was driving on road the front output on the t case let go. We never tore into the front slip yoke section of this t case to know it had another yoke inside of it. Like who the hell designs that crap? Either way it was on borrowed time as further inspection shows the welded shaft is compromised. It sounds like he is going to stab another t case in it for now and we are tracking down a old chev 350 th400 and then hes going to get an econobox in front of a 205. He already has a ford 205.

Sweet pit tarp from koh>
118471

It looks like the yoke ear inside let go and the rest of it imploded the case. 118472118473118474

Borrowed time>
118475118476

The next victim>118477

The future plans>
118478
 
Last edited:

Ashcat

Active Member
Location
Wisco
What was the purpose of that worthless output design and had you known about it what would your approach been? Not because metric BIIs are soooo cool sake/tech
 

YROC FAB.

BUGGY TIME
Vendor
Location
Richfield, UT.
The problem is that weld was too strong = twisted splines. Tisk tisk

I knew i should left some oil on the shaft when i was welding it.

What was the purpose of that worthless output design and had you known about it what would your approach been? Not because metric BIIs are soooo cool sake/tech

Only logical reason we can think of is maybe the front slip yoke portion comes off at a slight angle to help some crappy drive line angles of the factory bronco ttb. Had we known we probably would of tried to dual up one of these piles with the 205 hes got laying around. Its good it broke, now hes wised up and we are putting a chevy motor in it. :rofl:
 
Top