Cory Pimps out his runner.

YROC FAB.

BUGGY TIME
Vendor
Location
Richfield, UT.
The runner did good all week hauling around 4 of us at koh luckily as i was not the only one to blow my buggy engine. I just made sure not to idle it after it warmed up. if i kept it at about 1500rpms it would maintain 20psi of oil pressure. Every one got of kick out of my Epstein flag this year. Pro tip if you decide to spectate koh, Installed the biggest ugliest flag you can so you can see your ride when its parked with 1000 other shit boxes.
84926093_115531839901926_5060082652829188096_n.jpg84851396_10157148971841094_4485739873453473792_o.jpg84473098_10157148971656094_4487763047863025664_o.jpg
 

YROC FAB.

BUGGY TIME
Vendor
Location
Richfield, UT.
Well that 20lbs of oil pressure went to zero last spring while we was breaking snow drifts into my buddies cabin. Its sat since then till yesterday. I called all over looking for another good 3rz which sadly is just too hard to find and they want way too much for a worn out one. I went ahead and ordered all the AA parts to ls swap the ole gal. We got it in the shop and gutted the 4 banger out of it. i would like to have it done in time for KOH.


20211229_194043.jpg20211229_194050.jpg20211229_194054.jpg20211229_194100.jpg20211229_195057.jpg20211229_203037.jpg
 
Last edited:

NYCEGUY01

Well-Known Member
Location
Willard, UT
Yup. Cant beat 300hp for 500$

Hmmm.. Want 430 instead while youre at it ?........lol
I have one here on a stand I dont think Im gonna use.....
Gonna stick with a 99 Vortec smallblock I think...
5.3 - Edelbrock cam, ARP studs, LS1 heads, manley valves, ICT billet front drive, Jegs rear sump pan, MSD starter, blah, blah, blah....
 

NYCEGUY01

Well-Known Member
Location
Willard, UT
For 500$ sure. :rofl: i'll send a truck.
Not quite...lol I got into it pretty cheap for what it is though...
Id sell it for like $1650 with no intake or for another $500 with a new Edelbrock carb / MSD igntion setup.
Was built and put in a 32 Ford and then got removed for a blown flathead. Oldschool 😎
 

YROC FAB.

BUGGY TIME
Vendor
Location
Richfield, UT.
My flywheel and pressure plate showed up early so I took the engine out and installed everything. The original plan was to install and plumb the engine and drop the tyranny later to install them.

Had to grind the spacer to get the slave cylinder to mate.
20220109_220401.jpg
Slave cylinder alignment is poop
20220109_220944.jpg I installed a f body pan I had. I wanna modify a truck pan and swap them out later. 20220110_141725.jpg20220110_183556.jpg20220110_191142.jpg20220110_191150.jpg20220109_214341.jpg
 
Last edited:

YROC FAB.

BUGGY TIME
Vendor
Location
Richfield, UT.
Got this big old Flowmaster off of Austin's mint bastard. Reduced it down to 2.5" and a single inlet.
20220111_164651.jpg20220111_164705.jpg20220111_195255.jpg1200px-SideshowBob.jpg20220111_200051.jpg20220111_204624.jpgI was able to fish the entire exhaust all the way in to "U" pipe with only one union. 20220111_204642.jpg20220111_214505.jpgA little wrap where it gets close to the starter.20220111_214526.jpg
 

Attachments

  • 20220111_215855.jpg
    20220111_215855.jpg
    295.2 KB · Views: 6
Last edited:

YROC FAB.

BUGGY TIME
Vendor
Location
Richfield, UT.
It's my experience that girls in sweats rarely smile for pictures. Especially in cold shops. She must like you. Solid work.

She is known for always smiling around everyone she meets or just out in public. Also it was nice and toasty in the shop. She was sitting right where the gigantic natural gas heater blows. Thank you sir.
 
Top