General Tech The Mango Bastard - A Rockwell Buggy story

_Auzzy_

Current Rig: 12W Boots
Location
Richfield Utah
So long time no update, been wrapped up in everyone elses crap but this hitch home im telling everyone else to beat it and we are getting crap done!!

First off cory knocked out two big pieces we've been procrastinating for awhile now. got the fuel cell mounted and the roof bars fitted and burned in!
37101396_10217371157013590_3759711545106366464_n.jpg37120705_10217371158653631_2728158656573997056_n.jpg


He also gave me a quick lesson on his tig welder and i started playing with the floor pans

37101502_10217371161213695_8245927107662708736_n.jpg 37113052_10217371160573679_1684911074605793280_n.jpg
37085185_10217371157893612_677107882046521344_n.jpg

and while he was burning the top in i requested a helmet/wheel hook

37079214_10217371159733658_5980731716182999040_n.jpg
 

_Auzzy_

Current Rig: 12W Boots
Location
Richfield Utah
Then last night cory put in a good 10hrs into my dash! and im telling yal pics dont do it justice lol its fricking slick and tight fitting!

37130312_10217379927632850_947284715356815360_n.jpg37167473_10217379927792854_7501131902535860224_n.jpg37183284_10217379928272866_7292410472068808704_n.jpg

Once he was done with that he started on the driver side foot heat shield.
37137939_10217379928712877_6482903140722016256_n.jpg

while he did that i put in my second trans cooler and got my gas pedal built in

37167356_10217379928512872_5104763713005551616_n.jpg
 

_Auzzy_

Current Rig: 12W Boots
Location
Richfield Utah
Little update

First got the rear resies mounted
FB_IMG_1531906280776.jpg

Then got the throttle cable in and adjusted with a stop bracket

FB_IMG_1531906284249.jpg
FB_IMG_1531906288433.jpg


Then tonight I tackled the trans/exhaust tunnel and bracing my floor. Gonna add a 1" ring around the top of it for burritos since the exhaust is about 1.25-1.5" below it

FB_IMG_1531906292019.jpg
FB_IMG_1531906295240.jpg
 

_Auzzy_

Current Rig: 12W Boots
Location
Richfield Utah
Well not a whole lot, but some big stuff none the less.

Cory got the drivelines knocked out, the front and rear are the same length so he knocked out a spare too.
FB_IMG_1532431317480.jpgFB_IMG_1532431320530.jpgFB_IMG_1532431324033.jpgFB_IMG_1532431327092.jpgFB_IMG_1532431330478.jpgFB_IMG_1532431333816.jpgFB_IMG_1532431337036.jpg
 

YROC FAB.

BUGGY TIME
Location
Richfield, UT.
Well Austin has been gone too damn long and we want to wheel this thing sooner than later so i am finishing up and getting it ready to paint when he comes home in a few weeks.

I found me a 17year old kid named Kevin that wants to learn to fab and weld so he has been over the last few months doing all my slave work.:rofl: I would probably just wait for Austin to come home but this kid wants something to do so we tore into Austins buggy. The only thing we really have to do fab wise is the skids. The chassis needs finished welded and chromed up for paint, and finished torn down. We spent about 45min the other week and had the axles out and it upside down. Kevin has spent a few days finish welding out the bottom. I told him as long as his welds are better than Austins, which aint hard to do:rofl: then there wont be any problems. I drew up and cut out most the skid parts today.

Kevin welding away.
40844958_1872563022831979_2734838163942932480_n.jpg

40668751_1839710029477854_1720310366858117120_n.jpg40684528_1839710089477848_2898280288238960640_n.jpg
 

Attachments

  • 40844958_1872563022831979_2734838163942932480_n.jpg
    40844958_1872563022831979_2734838163942932480_n.jpg
    107.8 KB · Views: 1

YROC FAB.

BUGGY TIME
Location
Richfield, UT.
Just wrapping up Austins skids meow. I was going to bolt on the boat sides to but Austin reminded me that wasn't our original plan so they got welding on and the holes i cut to be bolted on will be nice drain hole now. We can access everything really well by removing just the bottom skid so the boat sides got burned in today by kevin. The bottom skid and engine skid bolt on reality easy with recessed bolt hole keeping the bolt heads safe and the bottom flat. I precut 3/8 holes for when we get around to buying some UHMW plastic to bolt onto latter. I <3 my plasma table.

Tomorrow i will finish gusseting the bottom side and maybe get it flipped right side up and start removing everything.

Austin will be home for 4 days on the 22nd so we will have it ready for him to paint (because i aint F'in doing that:shawn:) and then we will assembled and get it weighed for springs before he leaves.
41606918_1883722878382660_9221849707171545088_n.jpg

Kevin squeaked up in there to weld on some of inner skid tabs.
41608673_1883722795049335_1277594350691287040_n.jpg41663738_1883722748382673_5405334346242457600_n.jpg41669207_1883722931715988_6385744125718691840_n.jpg41701011_1883723075049307_3633815118673870848_n.jpg41685551_1883722845049330_2458468851080232960_n.jpg41684578_1883722968382651_451891616794279936_n.jpg

Recessed bolt heads41654947_1883723025049312_6074052958864015360_n.jpg
 
Top