Search results

heres one. Iam in the middle of swapping an engine tranny, etc... from a 93 cherokee into an 89. I have the wiring harness from the engine compartment out of the 93 sittin on the engine still. But will I have to swap anything else from the 93 like, the fusebox, the brain box (which is where on...

well here we go again. Last night I was driving around and ran over a coyote. When it was all said and done I noticed that my gauges where all over the place. my volt gauge was reading low, the oil pressure was pegged along with the temp gauge. When I turned off the lights everything would go...

I was wondering if a T-18 out of an 87 ford would fit into a 76 cj-5 with an 304 and a dana 20 t-case?

Iam planning on putting a set of 3/4 ton chevy axles under my 76 cj. Iam also going to convert the front 44 to crossover steering and I thought I would get somebody's input on buying either heim joints to make the swap or buying tie rod ends and threading the tubing for the chosen joint? I...

I was just wondering what the rules are for different classes in the competition Scene? also does RCAA or UROC have a lot of safety rules for example the role cage must connect to the frame in 8 places or something like that or the size of tubing that has to be used? thanks Kyle

I drive an 87 ford F-250 with a 302 Port injection, and the fuel pumps wont shut off. I can't find the relays to it either and I was wondering if somebody might know what is going on or maybe where the relays are at? Thanks Kyle

Iam planning on putting a 44 under the front of my dads jeep and I was wondering what all will it take to get crossover steering mounted on the axle? the 44 came out of 70's model chevy pickup. Kyle

I was wondering if the 429 block was the same as the 460 and if so, what is the difference other than the crank?

does anyboyd know if a ford 4spd OD will bolt inplace of a T-18, (on a 4wheel drive) thanks. Kyle

I was wondering if anybody knew if the ford 4spd OD will bolt in place of a Warner T-18 transmission. thanks. Kyle

What holds a better bead on 35x12.50 15. The 15x8 or the 15x10?

I have a 94 Cherokee that I plan on putting full size axles under with a coilovers on the front and 1/4 eleptical in the rear. I was wondering how would I go about mathematically figureing out how to make the three point for the rear, the 4 point for the front, and how to get it to ride evenly...

Iam having problems with my cherokee over heating and I have a new radiator, and new water pump and plenty of fluids, and I have asked a few people and some tell me to just pull out the thermastat and then other tell me that its a bad idea to pull it. so I figured I would just ask the people at...

I have a 79 Bronco that wont turn over. When I jump it using the starter solenoid it will turn over but not with the key. I was thinking the Neutral Safety switch but I don't know where it is on the 79 bronc. I don't know where I should start. either with the Neutral Safety switch or by...

I have a rotary engine in a mazda and I am having problems getting it to run very well. I seems that after I let it sit for a while and go out and try to start it, it will start right up but wont idle. Then the longer I try to start it the more gas comes out of the exhaust and when I check the...

I have a mazda RX-7 and haveing one hell of a time getting the pilot bearing out? I was wondering if anybody knew of any tricks to getting it out? Thanks.:D

I am pulling in engine out of an LTD and putting it into a bronco 351/m and I am wondering if it is easier to leave the torque converter on the tranner or on the flywheel when I go to put it in the bronco? I know on the chevy its best to leave it on the tranny but I have no idea on fords...

Ok maybe Iam missing something here but I don't understand why people will put 3 grand into there rig and then put on extended shackles???? Why? I figure spend that much you should go all out right? I don't know but let me know what you think?

Ok here is the thing I just pulled an engine out a 78 bronco, The engine is a 351 m. and the tranny is a c6 but the shaft that connects to the torque converter from the tranny was broke so I pulled to pump off and before I install the new one I was wondering if there is any trick or special way...

Well Ive been on here for a couple of weeks and just now decided to put a post in the Introductions. Well lets just say I only have 2 weeks of school left in Dove Creek Colorado, I spend most of my free time thinking and working on my vehicles, and in Sept. Iam going to Wyoming Tech, for...