What projects do you have on your plate....

[spencurai]

I have to :
1) change my body mounts on my YJ from stock mounts + 2" puck lift to DAYSTAR mounts with 1" built in.
2) Change the rear leafs on my zuk with fresh I just got from James K
3) install my Anti-Wrap bar when it gets here on my zuk
4) replace my plugs wires cap and rotor and coil on my YJ
the list goes on and on.....

 

[Caleb]

do I really wanna start listing??? I know I will miss a lot

1.install motor
2.fab brackets for radiator and install radiator
3.fab fan shroud
4.wire engine
5.build dual t-case setup(ordering adapter soon)
6.install tranny
7.install t-cases
8.build cage
9.install fuel cell
10.install seats and seat belts
11.build new "flat" dash
12.wire new dash
13.build flat skid plate/crossmember
14.fab winch mount and install winch
15.-20.everything I forgot right off the top of my head

I have a lot to do and I wish it was still warm

 

[Greg]

-Wire 220v to Garage, so I can......
-Finish building Tube Bender stand.
-Get and assemble 7MGE from a Shortblock (Have head rebuilt)
-Pull 22RE and replace with I6. (Find parts for Swap)
-Wire the damn thing.
-Swap in 44044's..... after building Drop Spring Hanger.
-Build killer, front Tube Bumper w/ new Bender!
-Bitchen Flatbed.
-Wire Power Windows.
-Install Super Birfs.
-Paint and install Fiberglass Fenders.
-Think about getting Coils in the rear.
-Get Supra to pass Emissions.


Ummmmm..... thats all I can think of at the moment........

 

[cruiseroutfit]

Put my superbirf in before tomorrow...

 

[2BIGTJ]

OK I had to sit down and think for a while I have so much to do.

- build a rear 60
- install a detroit in the rear
- install 5:13 gears
- build a truss for the rear
- put all brackets on the real axle
- put disc brakes on the rear
- build a front 44
- install a ARB in the front
- install 5:13 gears
- put all brackets on the front axle
- build all long arms
- build all the brackets on the frame
- fab the steering links
- buy Andys 38" tires
- buy and instal the skyjacker 8" springs
- finish the full roll cage
- have Andy build my drive shafts and install a short shaft kit
Also anything else that has to be done with a buildup like this, so any help would appreciated, it has to be done in( how many days until Easter) not long.

 

[Shawn]

Mine is easy.

Not touch the Cruiser

Build the CJ5/buggy
The list is to long for this project, however, it is getting shorter

 

[XRunner]

My next project will be a 1983 toy rock buggy. Motor in it will be a I6 1995 2jz-ge out of a 1995 toyota supra. Good for about 250 HP. But first l have to finnish my Red 93 Toyota XRunner which use to be an xtra cab but now looks more like a 4 door. It has a 7mgte I6 supra turbo motor pushing around 250 CHP but will soon have 300 RWHP. The truck needs a lot of body work and paint. Soon to post pics.

 

[harkinoff]

1. finish cage mounts on frame
2. reinstall all onboard air components
3. find seat to fit in back (dodge caravan)
4. finish rock sliders
5. build rear bumper
6. soft top
7. build tool and spare part boxes for rear
8. build spare tire mount to cage
9. fuel injection ? or just run my propane setup
10. install adjustable proportioning valve, finish rear disc conversion
11. decide if I'm going to keep it when its done or go dent it
up and wheel the piss out of it

 

[Hickey]

Greg, did you just type "power windows"? you are kidding, right?

 

[mbryson]

Get a job, a tow rig, and then a BEEETCHEN trail rig.

 

[sukaB]

I can take care of the trail rig part the rest is up to you.......
How about an 04 MBRYSON edition Black Wolf.......



Actually hawkins still has his chev truck for sale and also i have my burb and a 93 YJ too.

 

[Shawn]

Originally posted by mbryson
Get a job, a tow rig, and then a BEEETCHEN trail rig.

The Job:
Working with Habeeb at the quickie mart.

Tow Rig:
Subaru Legacy Wagon

Beetchen Rig:
Trecker

 

[Greg]

Originally posted by Jeremy
Greg, did you just type "power windows"? you are kidding, right?

Well..... NO!

My old doors were manual, but they took a beating and are now destined to be hacked up or junked. I got a set of doors in good cond, with Power Windows. I actually didn't even have any windows for the few months my truck was running!

 

[tv_larsen]

Oh man, I could list all night, but, my list to get ready for EJS:

1. Mail EJS registration -- Done
2. Get new tires -- Done
3. Fix cracked frame
4. Fix dash wiring
5. Relocate battery/relay/ECU
6. Remove inner fenders
7. Generous use of sawzall to open wheel wells
8. Build front cage/tie it into factory roll bar
9. Install rear shackle flip
10. Remove overload and extra leaf from rear springs
11. Make longer front shackles
12. Repair front driveshaft
13. Repair rear driveshaft
14. Cut top in half
15. Build tube doors
16. Weld plate over huge rust holes in floor
17. Prepare tow rig
18. what am I missing...........................?

 

[wort]

ive got to
-torch ifs
-fab and install dropped front spring hangers
-drill holes in the frame for rear shackles
-put on wagoneer springs
-modify my front axle for the electric locker
-pick up some mazda springs from PNP
-ect

 

[pokeyYJ]

My list:

1. Sell Pokey
2. Buy Gumby

 

[spencurai]

ohh and I got more.....

1) fix dash lights....they haven't worked since I got the YJ
2) install a reverse light.
3) weld the spare tire carrier stress fractures.
4) install a battery tie down contraption
5) straighten my zuk tie-rod
and the kicker



Figure out why my YJ keeps running if I leave it in reverse and turn off the ignition, somewhere there is a short that keeps the ignition on when the non existent reverse light is engaged. I can take the key out and close the doors and walk away with the shifter in reverse and it will stay running until I slip it into neutral and dis-engage the reverse light mechanism, then the motor turns off. go figure.....

 

[BlackSheep]

to be done before heading down to st. george next thurs
1. remove the snow that is packed throughout the cab of the jeep
2. put my cab top back on

and here's my list to be done before EJS
1. Pass Safety Insp (if necessary.....don't even know if it is required for me this year)
1.a. obtain and mount 3rd brake light
1.b. Figure out something for the fender flares
1.c. fix broken stud on right rear
2. Finish my taxes, get my return so I can
2.a buy a set of half doors with uppers
2.b. buy a new set of springs and longarm control arms (and associated parts and pieces) to make my rig a longarm.

 

[Hickey]

disassemble....
reassemble....
twice.

 

[Andy]

Originally posted by spencurai
2) install a reverse light.

Why do you need a reverse light? It just warns who ever you just ran over that your coming back for seconds, sierra club member/ hiker..... you get the picture.