ID Bronco
Registered User
- Location
- Idaho Falls, ID
I am looking for the knowledge of all of you gearheads. Many of you know the value of this much better than I do. I wrote this ad in anticipation of posting it, but just don't know what to ask.
Better as a project or just skip that and part it all out?
Any thoughts you all have would be appreciated.
It is/will be for sale if you are interested. Thanks.
1997 Titled Chevy Blazer (much of a 2020 was used on this build)
It is a project, not complete yet. It will need to be trailered.
I bought this project from an acquaintance who was building it to run the Everyman Challenge 4600 Class at KOH.
He ran out of money and ambition so I bought it and am selling the rig and or parts from it. I'd like to sell it complete if possible.
I know a lot about it but not everything since I have not been the one building it. Here is what I know, have been told.
It's a very cool project, finish it or use everything to build your own awesome rig.
Engine - 4.3 litre Vortec - This has been rebuilt and has been started but no miles on it since rebuild. It should be a screamer in this light rig.
Some modifications - New timing set
New push rods
Competition Cams 875-12 56-430-8 280 Intake .525 valve lift
Heads have Comp Cams double spring upgrade
New intake valve
Harland Sharp Custom full, self adjusting rocker rollers
ARP studs 135-7201
PCM was worked on by PowerLabs in Shelley ID and tuned up really well.
Cod air intake (to make room for the PSC reservoir)
Transmission - 2001 4L60 Automatic
Transfer Case - NP233 with slip yoke eliminator kit installed
Rear driveline included (from NP233 to 14 bolt)
Rear Axle - 14 Bolt Chevy with disc brakes, stock shafts, full spool, Ballistic Fab Shave kit installed, new 5.38 gears from East Coast Gear, full rebuild kit.
Front Axle - GM 2500 9.25 ifs front diff with new 5.38 gears, a Powertrax Lock Rite locker, H2 AWD one piece shaft 33 spline.
New extended axles/joints/boots for GM 2500.
Ballistic Fab pinion yoke protection (shovel) and 1410 pinion yoke.
Rear Suspension - 63" New Chevy leaves, new shackles and bushings.
Traction bar
Adjustable shock hoops with larger holes for coilovers. (coilovers already sold)
Room for Anti-rock but it is sold too.
Front Suspension - Custom long arm IFS, extended A arms, Maxx Suspension adjustable torsion keys and set up for 10" coilovers. (coilovers sold)
Ballisitic Fab Uniballs drilled out to 1" hardware.
Fabtech cradle, Shock mounts.
Front steering uses BEEFY DOM tubing for strength, same design as Cognito uses but much larger and heavier wall tube and heims.
Steering - Full PSC kit for hydro assist including: Power steering pump, reservoir, orbital, PSC power steering pump (ported), PSC Ram 6 3/4 stroke, fluid cooler.
The system is installed but has not been used yet, it's all brand new.
Larger brake booster has been installed.
Custom rear bumper
The body is pretty straight, not a lot of damage. 2000 front grill.
The bad:
Body is stripped except dash, steering wheel, shifter, seatbelts. No glass.
It needs brake lines throughout.
The starter solenoid is acting up.
_____________________________________
Other thoughts:
I have other parts that could be included in the sale for extra cash. Fuel Cell with fuel pump, filler neck, ect. Wheel Spacers to match front and rear track width, window nets, some misc other things.
It needs a lot of little things to make it a runner, or part it out as you see fit. I may end up doing that if it doesn't sell, so shoot me an offer on major components if you're interested in them.
I'm open to serious questions, maybe a trade (maybe) and could deliver it for a fee within 300ish miles of Idaho Falls, ID. I can help load it on your trailer too.
Better as a project or just skip that and part it all out?
Any thoughts you all have would be appreciated.
It is/will be for sale if you are interested. Thanks.
1997 Titled Chevy Blazer (much of a 2020 was used on this build)
It is a project, not complete yet. It will need to be trailered.
I bought this project from an acquaintance who was building it to run the Everyman Challenge 4600 Class at KOH.
He ran out of money and ambition so I bought it and am selling the rig and or parts from it. I'd like to sell it complete if possible.
I know a lot about it but not everything since I have not been the one building it. Here is what I know, have been told.
It's a very cool project, finish it or use everything to build your own awesome rig.
Engine - 4.3 litre Vortec - This has been rebuilt and has been started but no miles on it since rebuild. It should be a screamer in this light rig.
Some modifications - New timing set
New push rods
Competition Cams 875-12 56-430-8 280 Intake .525 valve lift
Heads have Comp Cams double spring upgrade
New intake valve
Harland Sharp Custom full, self adjusting rocker rollers
ARP studs 135-7201
PCM was worked on by PowerLabs in Shelley ID and tuned up really well.
Cod air intake (to make room for the PSC reservoir)
Transmission - 2001 4L60 Automatic
Transfer Case - NP233 with slip yoke eliminator kit installed
Rear driveline included (from NP233 to 14 bolt)
Rear Axle - 14 Bolt Chevy with disc brakes, stock shafts, full spool, Ballistic Fab Shave kit installed, new 5.38 gears from East Coast Gear, full rebuild kit.
Front Axle - GM 2500 9.25 ifs front diff with new 5.38 gears, a Powertrax Lock Rite locker, H2 AWD one piece shaft 33 spline.
New extended axles/joints/boots for GM 2500.
Ballistic Fab pinion yoke protection (shovel) and 1410 pinion yoke.
Rear Suspension - 63" New Chevy leaves, new shackles and bushings.
Traction bar
Adjustable shock hoops with larger holes for coilovers. (coilovers already sold)
Room for Anti-rock but it is sold too.
Front Suspension - Custom long arm IFS, extended A arms, Maxx Suspension adjustable torsion keys and set up for 10" coilovers. (coilovers sold)
Ballisitic Fab Uniballs drilled out to 1" hardware.
Fabtech cradle, Shock mounts.
Front steering uses BEEFY DOM tubing for strength, same design as Cognito uses but much larger and heavier wall tube and heims.
Steering - Full PSC kit for hydro assist including: Power steering pump, reservoir, orbital, PSC power steering pump (ported), PSC Ram 6 3/4 stroke, fluid cooler.
The system is installed but has not been used yet, it's all brand new.
Larger brake booster has been installed.
Custom rear bumper
The body is pretty straight, not a lot of damage. 2000 front grill.
The bad:
Body is stripped except dash, steering wheel, shifter, seatbelts. No glass.
It needs brake lines throughout.
The starter solenoid is acting up.
_____________________________________
Other thoughts:
I have other parts that could be included in the sale for extra cash. Fuel Cell with fuel pump, filler neck, ect. Wheel Spacers to match front and rear track width, window nets, some misc other things.
It needs a lot of little things to make it a runner, or part it out as you see fit. I may end up doing that if it doesn't sell, so shoot me an offer on major components if you're interested in them.
I'm open to serious questions, maybe a trade (maybe) and could deliver it for a fee within 300ish miles of Idaho Falls, ID. I can help load it on your trailer too.